13 grams (still at 15-16 cu) the damping again can be reduced toward no damping, since the increased cartridge mass is adding more inertia (this is my rational).Ī low cu of 10 and less, with a low cartridge mass, e.g. On the other hand, with a cu of about 15-16 (medium stiff) and a cartridge mass of ~9 grams I find a medium immersion somewhere between the two markings suitable, and as the cartridge mass goes up to e.g.
#SME TONEARM SPACER SERIES#
In my experience, a low cartridge weight ~ 6 gram and high/soft compliance > 20 cu, asking for a light mass arm, I would use no damping at all, lifting the screw pin up past the first marking (tray filled to the correct level with the correct viscosity silicone gue). SME Tonearms SME 3009 / 3012 / Series III P1 Spacer P1 Spacer - Genuine (NOS) SME 30 & Series III P1 Spacer Plate Adapter This Spacer Plate Adapter will allow you to mount your SME 3009 & Series III tonearm on virtually turntable where arm height is an issue. This is all very finicky and in final analysis it'd STILL depend on your listening impression what you prefer of course. In other words pretty much fully immersed in the silicone. 11 gram, this if the pin is screwed down to the second marking for example. By this shifting the arm mass toward the quoted upper range of 10-11 gram e.g. However, if you use the silicone damping tray function (some more or less) it can be argued that it would effect the arm mass slightly too. I listen maninly to jazz and rock with a little classical.Sorry, I also would need the cu (compliance unit) of course, the arm mass for the SME V I'd use as 10.5 gram. Oh and sometime I may try it on my Garrard 401 with Audio Origami PU7 and Shelter 501 Mk2. Though excellent sounding it’s no match for my analogue source. I also have an Aurender N100H and an Auralic Vega for digital playback.
This feeds the phono input of my Crayon CFA 1.2 which in turn drives my ART Emotion loudspeakers. My arm is a Linn Akito with an Ortofon OM20 cartridge. I would be interested if there were any other mats you might consider worthy of trying. Though I’m in no hurry as I am really enjoying it right now. I’ve got a 1mm nitrile cork mat that I will try between the LH-2 and a Boston Audio Mat 1 to prevent possible slippage at the interface. Might try a thicker one.Ĭurrently I am using an Oyaide BR-12 that I used on the Lenco platter and that is very enjoyable. So far I have tried a 1mm pigskin mat which I didn’t really care for, though detailed it was a bit lifeless. Sadly not all recordings are equal but most benefit and all are enjoyable. SME spacer for the tone arm which provides sufficient height to use with the raised motor board (although I think the P.I. It is now much easier to find a satisfactory listening level and it’s not as loud as before. Comes with original packing box and user manual. Audiocraft XTC-TP150 1.5m pair 4N/6N twin core double shielded DIN to RCA tonearm output cable. Suitable arm: All models of SME, or all kind of SME arm mount base's tonearms. SME had redesigned their vintage S2 series arm to become a better match to the popular high-compliance, low-tracking-force, phono cartridges of that day. Type: Arm spacer for use when the turntable surface is more then 1 5/8' (41mm) above the surface on which the arm is mounted. The SME 3009 S2 Improved fixed headshell tonearm. Soundstage has expanded in width and depth and the imagery within is more stable. Mounting an SME 3009 improved to a TD160. It may be needed when using short bodied cartridges such as Koetsu. With this spacer you can accurately mount your SME tonearm on any turntable that has an extra tall platter. The frequency extremes have been extended and are very clean and fast. SME P1 Metal Spacer Genuine SME Part This Spacer Plate Adapter allows you to mount your 3009 or 3012 tonearm (Series 1, 2 or 3) on almost any turntable where arm height is an issue - including the Garrard 301, 401 & Thorens TD-124. For instance the next will log a print job, print the file, then take away it. As soon as confirmed, remove the check schedule from the automated system and let it go reside.
#SME TONEARM SPACER UPGRADE#
Bass initially appears to be lighter but when it is present it really makes itself known. Gross sales system has a peak demand between 6PM-9PM, HR techniques has a peek demand between 1PM to 5PM, Stock administration system has a peak demand between 9 AM to 1 PM. Incognito Tonearm Cardas Silver Litz Universal Rewire Kit £329.99 IsoKinetik IsoEnd Rega RB250 Upgrade End Stub £19.99 IsoKinetik ISOtone SME 3009 1&2 Rewire Kit £24. It makes some difficult music more listenable.
Music flows and there is better continuity throughout a track. Sounds just swell from the background too. There is now very little background noise and the detail within the background is more coherent. 5 mm thick acrylic tonearm base spacer for SME 3009 to 3012. SME 3012 S2 Long tone arm shell cable main weight Inside Force Canceller. The platter has changed the dynamic presentation of well loved recordings significantly. 8 mm thick metal tonearm base spacer for SME 3009 to 3012.
0 kommentar(er)
